PUR foam/ gun
#3946346
08/16/13 02:19 PM
08/16/13 02:19 PM
|
Joined: Jan 2011
Posts: 5 Lawrence, Kansas
TJP
OP
trapper
|
OP
trapper
Joined: Jan 2011
Posts: 5
Lawrence, Kansas
|
I'm looking to buy the gun and foam. Does the case hold the gun and can of foam together? Or do you have to find somewhere else to store them when they are together? I see it says do not ever take the can off the gun unless you are changing cans.
Last edited by TJP; 08/16/13 02:44 PM.
|
|
|
Re: PUR foam/ gun
[Re: Bob Jameson]
#3946471
08/16/13 04:18 PM
08/16/13 04:18 PM
|
Joined: Jun 2011
Posts: 247 rhode island
ritrapper
trapper
|
trapper
Joined: Jun 2011
Posts: 247
rhode island
|
We remove the foam can after each use from the gun and keep the screw on foam cleaner can, spray until clean and keep it there until the next use. We have used our last gun for 6 years by following this proceedure.
That goes against everything the pur foam rep said. I was always told keep The can on the gun until empty, the problem is I can never empty a can because the gun always gets plugged inside the trigger area. This is my second gun (the economy model).Im going to try it your way and see if it helps. Is the more expensive model that much better?
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3946495
08/16/13 04:41 PM
08/16/13 04:41 PM
|
DaveK
Unregistered
|
DaveK
Unregistered
|
The expensive one clogs too. We usually leave the can on until done, and clean periodically. I figured that the dry foam bits would clog gun....if you removed the can without cleaning top of can. I just keep buying guns...ugh.
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3946736
08/16/13 08:07 PM
08/16/13 08:07 PM
|
Joined: Feb 2012
Posts: 1,883 Northeast Wisconsin
NE Wildlife
trapper
|
trapper
Joined: Feb 2012
Posts: 1,883
Northeast Wisconsin
|
Last summer I think I went through two short And one long gun, this year as of yet I haven't had One gum up on me! This year I have been using Cleaner when I feel the can is about half empty and whenever I place a new can on! I have been gettin a lot of cans That only last for half the can! I think maybe it's the weird Angles I'm forced to use the can at!
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3947240
08/17/13 06:40 AM
08/17/13 06:40 AM
|
Joined: Dec 2006
Posts: 7,600 SW Pa
Bob Jameson
trapper
|
trapper
Joined: Dec 2006
Posts: 7,600
SW Pa
|
Spray cleaning the check ball area of the gun completely after a foam can is removed / changed is a given I would think.Dried foam will in time impede or restrict the spring valve movement of the check ball if this isnt done regularly. All the things I have mentioned are a good procedure I learned to follow and will ensure that you will get the most time served from your pageris guns.I was going thru several guns both long and short barrel models in what I deemed an unreasonable time period. The Long guns are more prone to seizeing due to their length and more potential clogging surface area we found. Keeping the cleaning can attached to the guns between use has been the key for maintaining working guns for us. You may use more cleaner then you are accustomed to using and waste a little foam due to the clean out process. However, the use of small amounts of each the product is justified in my experience. If you can't condition yourself or your employees to an alternative practice of pageris gun maintenance you can always keep buying more guns like Paul. I bet the company and dealers selling guns know when bat season rolls around. I guess Paul has WCS on speed dial this time of year.LOL
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3947293
08/17/13 08:12 AM
08/17/13 08:12 AM
|
Joined: Jan 2013
Posts: 32 OH
Eric Arnold
trapper
|
trapper
Joined: Jan 2013
Posts: 32
OH
|
Foam guns fail for a variety of reasons. Sometimes it is poor manufacturing but mainly the faults come from the users. The foam itself has an expiration date that can be found on the bottom of each can. As Bob pointed out, how you store the foam is just as important as using fresh foam. Let's face it, if you're using bad product you're going to get bad results.
A main way that guns get ruined is how they are cleaned. Running cleaner through the gun will eat away at the plastic O ring seal and allow air (e.g. moisture) to enter causing the foam to cure in the barrel. Normally, this is just at the tip which as Bob pointed out prevents the cable from moving when the trigger is depressed. This can be fixed several times by gently grinding away a very small portion of the barrel tip with a Dremel tool. Just make sure you go very slowly and check the gun frequently so that you don't remove too much material and permanently ruin the gun. If the gun is made by Pageris, you are supposed to be able to return it to the manufacture to have it fixed at no cost which is the better solution.
Bob's system works well mainly because he doesn't keep foam on the gun and by running the cleaner through the barrel keeps any cure from happening. Where most operators have a problem is that they run a can of foam, let it sit on the gun until empty then run cleaning solution through it along with running a knife or other metal object over the tip to remove dried foam in order to use the gun again or by dragging it over brick/stone surfaces. This process will destroy the internal O ring and damage the tip allowing air to enter the barrel.
If you are going to keep foam on a foam gun per the recommendations, do not clean the inside of the gun, run metal over the tip, or drag the tip over any hard uneven surface. Instead, use the spray cleaner to clean the tip after each application and use add on syringes and needles to protect the tip. Also keep the foam stored at room temperatures at all times, don't allow the foam on the gun to go bad (don't replace a can with one that will expire in a month and then not immediately use it) and make sure the foam can seal has not become loose.
As long as there are no defects with the gun itself, these steps will keep the gun working for years. Or, use Bob's technique and take the foam out of the equation.
Eric Arnold Publishing Editor W.C.T. Magazine Editor The Fur Taker Magazine
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3948132
08/17/13 07:13 PM
08/17/13 07:13 PM
|
Joined: Apr 2010
Posts: 111 NM
HD_Wildlife
trapper
|
trapper
Joined: Apr 2010
Posts: 111
NM
|
I should have added though, if I was running lots of it, I'd be following Bob J's recommended treatment. Just a little disclaimer there.... Glad it helped!
|
|
|
Re: PUR foam/ gun
[Re: TJP]
#3950217
08/18/13 10:14 PM
08/18/13 10:14 PM
|
Joined: Apr 2010
Posts: 30 St. Louis area
Dave Schmidt
trapper
|
trapper
Joined: Apr 2010
Posts: 30
St. Louis area
|
It helps, I think, to clean the tip with plain ol' acetone on a rough rag or those steel wool pads used for scrubbing pots. Then put a little Vaseline over the tip and a cap over that.
ALL OUT Wildlife Control
|
|
|
|
|