Home

Bats (metal roofs) biggest job yet!

Posted By: Pez77

Bats (metal roofs) biggest job yet! - 09/26/14 10:10 PM

I have been doing ADC work for 2 years now ! This is my biggest job yet! Not a lot of pictures as I was trying to beat the heat! Bats were literally landing o
n the metal roof and claiming under the ridge , gaining access to the attic! Had to seal 4 different ridges , both sides on every one. Used a roof cushion((This word is unacceptable on Trapperman) pad) inched my way out to the very end and then worked back to center! Tried repelling and that was to much back tracking! Hot metal roof ! Very pointy ridge cap makes for a very sore bum! Screened a bunch of louvres from an 80 ft boom lift! We needed a 120 footer but it is only available for a week at a time ! 12 grand, church wasn't paying for that so we had to skip a couple if chimneys! I could not believe the bats were able to climb up that metal, that is a steep roof ! Needless to say i will be re evaluating my valve installs ! Very old Catholic Church these bats are gonna put a lot of pressure on this building i have never seen such a massive colony! When doing my inspection they were flying all over the attic, which i also thought was pretty unusual! You learn new things every day in this job though!
Posted By: DaveK

Re: Bats (metal roofs) biggest job yet! - 09/26/14 10:15 PM

You sound very excited!
Posted By: Pez77

Re: Bats (metal roofs) biggest job yet! - 09/26/14 10:17 PM

Excited to be done! I really enjoy the bat work especially when others have failed
Posted By: DaveK

Re: Bats (metal roofs) biggest job yet! - 09/26/14 10:28 PM

I can tell!

http://m.youtube.com/watch?v=VSKn8RlD7Is
Posted By: Pez77

Re: Bats (metal roofs) biggest job yet! - 09/26/14 10:34 PM

I posted from my phone , and the period and the last letter in the alphabet do not work, Man i love me some Seinfeld though!
Posted By: Vinke

Re: Bats (metal roofs) biggest job yet! - 09/27/14 01:15 AM

Point taken..............
Posted By: Lundy

Re: Bats (metal roofs) biggest job yet! - 09/27/14 02:17 AM

At least it wasn't all in CAPS!

Good job. Congrats.
Posted By: Pez77

Re: Bats (metal roofs) biggest job yet! - 09/27/14 05:58 PM

Thanks guys, i have been reading on here for a few months , but every problem i encounter there is already a thread! So I was just wanting to post something! I am just going to appologize in advance for any technology or grammatical errors i make, there is a reason i stopped going to college and got into ADC work! Any other guys use sheet metal attached to the end of your exclusion valves , in which you can not create a steep enough angle (ie soffit roof interfaces ) this makes me totally rethink that concept!
Posted By: DaveK

Re: Bats (metal roofs) biggest job yet! - 09/28/14 12:20 AM

Nope.....just keep it in the air.
Posted By: Pez77

Re: Bats (metal roofs) biggest job yet! - 09/28/14 01:29 AM

Keep what in the air and how
Posted By: DaveK

Re: Bats (metal roofs) biggest job yet! - 09/28/14 01:37 AM

The tube. Just keep the end of the tube in the air. It works like an inverse minnow trap.
Posted By: Pez77

Re: Bats (metal roofs) biggest job yet! - 09/28/14 01:41 AM

So just a couple inches off the roof? Or do you have a certain angle that is more effective?
Posted By: Lundy

Re: Bats (metal roofs) biggest job yet! - 09/28/14 01:49 AM

I use 3 inch or 4 inch stove pipe. 1/4 inch hardware cloth at the opening, sometimes, on low slopes, I add enough pipe to get to the roof edge.
Posted By: DaveK

Re: Bats (metal roofs) biggest job yet! - 09/28/14 12:01 PM

5 to 6 inches from a surface.
© 2024 Trapperman Forums